Close
ATV12HU22M2 View larger

ATV12HU22M2

Square D (Schneider Electric)

Square D (Schneider Electric)

3606480071102

New Factory Sealed - Original product -12 Months Warranty

Variable speed drive ATV12 - 2.2kW - 3hp - 200..240V - 1ph - with heat sink

More details

$447.80 TAX INCLUDED

Usually Dispatched 7 -10 days

Data sheet

Poles Description1P
Frame TypeAltivar 12
Supply Voltage200..240V
Motor HP3 HP
Motor Power KW1.5 KW

More info

Main
range of product
Altivar 12
product or component type
Variable speed drive
product destination
Asynchronous motors
product specific application
Simple machine
assembly style
With heat sink
component name
ATV12
quantity per set
Set of 1
EMC filter
Integrated
built-in fan
With
network number of phases
1 phase
[Us] rated supply voltage
200...240 V - 15...10 %
motor power kW
2.2 kW
motor power hp
3 hp
communication port protocol
Modbus
line current
24 A 200 V
20.2 A 240 V
speed range
1...20
transient overtorque
150...170 % of nominal motor torque depending on drive rating and type of motor
async motor control profile
Quadratic voltage/frequency ratio
Sensorless flux vector control
Voltage/frequency ratio (V/f)
IP degree of protection
IP20 without blanking plate on upper part
noise level
45 dB
Complementary
supply frequency
50/60 Hz +/- 5 %
type of connector
1 RJ45 Modbus on front face
physical interface
2-wire RS 485 Modbus
transmission frame
RTU Modbus
transmission rate
4800 bit/s
9600 bit/s
19200 bit/s
38400 bit/s
number of addresses
1...247 Modbus
communication service
Read holding registers (03) 29 words
Write single register (06) 29 words
Write multiple registers (16) 27 words
Read/write multiple registers (23) 4/4 words
Read device identification (43)
prospective line Isc
<= 1 kA
continuous output current
10 A 4 kHz
maximum transient current
15 A 60 s
speed drive output frequency
0.5...400 Hz
nominal switching frequency
4 kHz
switching frequency
2...16 kHz adjustable
4...16 kHz with derating factor
braking torque
Up to 70 % of nominal motor torque without braking resistor
motor slip compensation
Adjustable
Preset in factory
output voltage
200...240 V 3 phases
electrical connection
Terminal 5.5 mm² AWG 10 L1, L2, L3, U, V, W, PA, PC
tightening torque
1.2 N.m
insulation
Electrical between power and control
supply
Internal supply for reference potentiometer 5 V DC 4.75...5.25 V 10 mA overload and short-circuit protection
Internal supply for logic inputs 24 V DC 20.4...28.8 V 100 mA overload and short-circuit protection
analogue input number
1
analogue input type
Configurable voltage AI1 0...10 V 30 kOhm
Configurable voltage AI1 0...5 V 30 kOhm
Configurable current AI1 0...20 mA 250 Ohm
discrete input number
4
discrete input type
Programmable LI1...LI4 24 V 18...30 V
discrete input logic
Negative logic (sink) > 16 V < 10 V 3.5 kOhm
Positive logic (source) 0...< 5 V > 11 V
sampling duration
20 ms +/- 1 ms logic input
10 ms analogue input
linearity error
+/- 0.3 % of maximum value analogue input
analogue output number
1
analogue output type
Software-configurable voltage AO1 0...10 V 470 Ohm 8 bits
Software-configurable current AO1 0...20 mA 800 Ohm 8 bits
discrete output number
2
discrete output type
Logic output LO+, LO-
Protected relay output R1A, R1B, R1C 1 C/O
minimum switching current
5 mA 24 V DC logic relay
maximum switching current
2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay
2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay
3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay
4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
acceleration and deceleration ramps
Linear from 0 to 999.9 s
S
U
braking to standstill
By DC injection <= 30 s
protection type
Against input phase loss in three-phase
Thermal motor protection via the drive by continuous calculation of I²t
Line supply overvoltage
Line supply undervoltage
Overcurrent between output phases and earth
Overheating protection
Short-circuit between motor phases
frequency resolution
0.1 Hz display unit
Converter A/D, 10 bits analog input
time constant
20 ms +/- 1 ms for reference change
marking
CE
operating position
Vertical +/- 10 degree
height
142 mm
width
105 mm
depth
156.2 mm
product weight
1.4 kg
functionality
Basic
specific application
Commercial equipment
Variable speed drive application selection
Commercial equipment : mixer
Commercial equipment : other application
Textile : ironing
motor starter type
Variable speed drive
Environment
electromagnetic compatibility
Immunity to conducted disturbances level 3 EN/IEC 61000-4-6
Surge immunity test level 3 EN/IEC 61000-4-5
Voltage dips and interruptions immunity test EN/IEC 61000-4-11
Electrical fast transient/burst immunity test level 4 EN/IEC 61000-4-4
Electrostatic discharge immunity test level 3 EN/IEC 61000-4-2
Radiated radio-frequency electromagnetic field immunity test level 3 EN/IEC 61000-4-3
electromagnetic emission
Radiated emissions environment 1 category C2 EN/IEC 61800-3 2...16 kHz shielded motor cable
Conducted emissions with integrated EMC filter environment 1 category C1 EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable 5 m
Conducted emissions with additional EMC filter environment 1 category C1 EN/IEC 61800-3 4...12 kHz shielded motor cable 20 m
Conducted emissions with additional EMC filter environment 1 category C2 EN/IEC 61800-3 4...12 kHz shielded motor cable 50 m
Conducted emissions with additional EMC filter environment 2 category C3 EN/IEC 61800-3 4...12 kHz shielded motor cable 50 m
Conducted emissions with integrated EMC filter environment 1 category C2 EN/IEC 61800-3 4...16 kHz shielded motor cable 5 m
Conducted emissions with integrated EMC filter environment 1 category C2 EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable 10 m
product certifications
CSA
C-Tick
GOST
NOM
UL
vibration resistance
1 gn EN/IEC 60068-2-6 13...200 Hz
1.5 mm peak to peak EN/IEC 60068-2-6 3...13 Hz drive unmounted on symmetrical DIN rail
shock resistance
15 gn EN/IEC 60068-2-27 11 ms
relative humidity
5...95 % without condensation IEC 60068-2-3
5...95 % without dripping water IEC 60068-2-3
ambient air temperature for storage
-25...70 °C
ambient air temp for op
-10...50 °C protective cover from the top of the drive removed
50...60 °C with current derating 2.2 % per °C
operating altitude
> 1000...2000 m with current derating 1 % per 100 m
<= 1000 m without derating
Offer Sustainability
Sustainable offer status
Green Premium product
RoHS (date code: YYWW)
Compliant  - since  0901  -  Schneider Electric declaration of conformity Schneider Electric declaration of conformity
REACh
Product environmental profile
Product end of life instructio
Contractual warranty
Period
18 months

21 other products in the same category

Schneider Partner

Schneider Electric Authorised distributor

Shipping Partner

DHL Express Delivery

Secure Payments

Scure site globalsign

Close